Analysis of Operation Test of Melt Index Tester
The melt index testing-equipment' target='_blank'>tester is used to characterize the flow properties of thermoplastic polymers in a viscous flow state, and to determine the melt mass flow rate (MFR) and melt volume flow rate (MVR) of thermoplastic resins. Polycarbonate, nylon, fluoroplastic, polyarylsulfone and other engineering plastics, also suitable for non-woven fabrics, meltblown fabrics, polyethylene, polystyrene, polypropylene, ABS resin, polyoxymethylene resin and other materials with low melting temperature Test, (Hong Kong) Co., Ltd. is the manufacturer, welcome to inquire. Applicable standards: GB/T3682, ISO1133, GB/T9643, JB/T5456, ASTM/D1238-98 Main parameters: 1. Extrusion discharge part Discharge port diameter:Φ2.095±0.005mm, outlet length: 8.000±0.025 mm; Charging barrel diameter:Φ9.550±0.025mm, charging barrel length: 152±0.1 mm; Piston rod head diameter: 9.475±0.015mm, Rod Tip Length: 6.350±0.100 mm; 2. Standard test load (a complete set of weights of 8 grades); 3. Temperature range: conventional room temperature——400℃ (500℃ optional); 4. Constant temperature accuracy:±0.5℃; 5. Display resolution: 0.1℃; 6. Cutting method: manual or automatic cutting; 7. Temperature recovery time: less than 4 minutes. Operation test: 01. Turn on the power supply, turn on the power switch, the green power indicator light is on, set the test temperature, and the red indicator light is on when heating. 02. Standby for 20 minutes, that is, the preset temperature can be stabilized before starting to work. 03. Sample preparation, weigh 4--5g on the balance, and prepare the sample for testing. 04. Add materials, when the temperature is stable, you can add materials. Take out the material rod, put it lightly on the high temperature resistant object, insert the funnel into the barrel, and vibrate the funnel while feeding, so that the material leaks quickly. After the feeding is completed, use the pressing rod to compact the material to reduce air bubbles, then insert the feeding rod, place the positioning sleeve, and put on the weight tray (the feeding operation must be completed within one minute). 05. After feeding, preheat for 4-6 minutes, add the required weights, and prepare for cutting and sampling. 06. When the material rod descends to the lower marking line, start timing and cutting. The test was stopped when it descended to the upper marked line. The cutting sample should be between the upper and lower marking lines of the material rod. 07. The cutting interval of each spline is determined according to the measured object. Generally, it is cut once every 60s or 30s. The length of each spline is generally about 20mm---50mm. 08. Select and weigh the splines, discard the splines with visible bubbles, and weigh the remaining splines (at least three) one by one, accurate to 0.0001g, and calculate the average weight. 09. Calculate the result and find the melt index. 10. After the test is completed, clean the material rod, barrel and die with clean gauze while it is hot for the next test. 11. After cleaning, put on the feeding rod, turn off the power switch, and cut off the power supply.
GESTER International Co.,Limited's products comply fully with all compatible producing regulations.
There is always a question of how to tensile tester manufacturers, but have you ever thought about the price point? Go to GESTER Instruments to get cost effective offer.
According to the market analysts, exports from GESTER International Co.,Limited facilities in China will exceed the forecast.
Natural has the distinct tensile tester manufacturers which is irreplaceable.
Undoubtedly, textile testing equipment are made with advanced equipment.
Safety gloves are critical personal protective equipment (PPE) used in industries such as manufacturing, welding, construction, firefighting and chemical processing. To ensure reliable protection, gloves must undergo strict performance testing before entering the market.
Professional gloves testing equipment helps manufacturers evaluate important properties including cut resistance, thermal protection, contact heat resistance, tensile strength and impact protection. By selecting suitable testing machines, companies can improve product quality, meet international standards and reduce safety risks.
This complete buying guide introduces the main types of glove testing equipment, explains their applications and provides practical advice on choosing the right solution for your laboratory or production requirements.
Choosing the right abrasion testing equipment is essential for obtaining accurate and repeatable wear resistance results. DIN Abrasion Tester and Taber Abrasion Tester are two widely used abrasion testing machines, but they are designed for different material types and testing purposes.
This article provides a detailed comparison between DIN Abrasion Tester and Taber Abraser, covering their working principles, specimen requirements, industry applications, standard compliance, technical characteristics, operation features and practical advantages. DIN Abrasion Tester is mainly designed for rubber, elastic materials, tires, conveyor belts and footwear soles, while Taber Abrasion Tester is suitable for flat materials such as coatings, textiles, plastics, leather, metals and decorative surfaces.
By understanding the differences between these two abrasion testing methods, laboratories can select the most suitable abrasion tester based on sample geometry, testing standards and production quality control requirements.
Quick links
Products