Analysis of test method for resistance to draw of cigarettes
Cigarettes are a common type of consumer product in daily life. The question of whether cigarettes are good or bad and whether they should be banned will not be discussed in this article. Scope: This standard specifies the method for determining the draw resistance of cigarettes. This standard applies to all kinds of cigarettes. Normative references: The following standards contain provisions which, through reference in this standard, constitute provisions of this standard. At the time of publication, the editions indicated were valid. All standards are subject to revision and parties using this standard should explore the possibility of using the latest edition of the following standards. GB/T5606.1-1996 Cigarette Sampling GB/T16447-1996 Tobacco and Tobacco Products Conditioning and Atmospheric Environment Determination Principle: Under standard conditions, when a steady airflow of 17.5mL/s flows through the cigarette sample When , the pressure difference between the two ends of the sample is the suction resistance of the sample. Instruments and equipment: 1. Instruments for measuring cigarette resistance should meet the following requirements:— Air flow: 17.5mL/s;— Probe: It can seal and measure the sample. During the measurement, the outlet end of the sample is inserted into the probe by 9mm, and there should be a layer of film in the test head. During the measurement, the film completely wraps the sample in the probe, and there should be no air between the wrapped part of the film and the sample;— Range->5kPa; resolution: 10Pa;— Measured value display accuracy: 1OPa, 2. A set of standard bars: The difference between the standard values of two standard bars is not less than 1kPa; the accuracy (relative error) of the standard bars is 1%. Measurement steps: Adjust the sample according to GB/T 16447, and Tested under corresponding environmental conditions. 1. Turn on the power of the instrument and preheat to make it stable. 2. Connect the air circuit. 3. Use the high and low standard rods to calibrate the instrument respectively, so that the relative error between the displayed value of the instrument and the standard value of the standard rod does not exceed 1%. 4. Insert the outlet end of the sample into the probe of the instrument, and the insertion depth is 9mm , so that the film wraps the sample inside the probe tightly. 5. The resistance reading should be obtained within 2-3s after the sample is inserted into the instrument
GESTER International Co.,Limited is willing to push up our sleeves and wade into unknown territory with equal parts fearlessness and optimism.
Dedicated to bringing you professional textile testing equipment solutions and related products – from tensile tester manufacturers to tensile tester manufacturers, GESTER International Co.,Limited is your textile testing equipment helper. Visit us at GESTER Instruments.
For more textile testing equipment tensile tester manufacturers reviews, tips and advice on choosing a washer and dryer for you and your family, please visit GESTER Instruments,where you can also choose the you are looking for.
The air permeability tester is a high-precision testing instrument designed to evaluate the breathability of PPE materials, textile fabrics, non-woven fabrics, woven fabrics, and industrial filter media. It plays a critical role in quality control, product development, and laboratory research across multiple industries including PPE, textiles, automotive interiors, and filtration systems.
Modern instruments such as the GT-C27 Air Permeability Tester are developed with advanced sensor systems, automated control logic, and multi-standard compatibility to ensure reliable and repeatable results. Complying with global standards such as ISO 9237, ASTM D737, DIN 53887, and GB/T 5453, it guarantees internationally recognized testing performance.
With high automation, accurate pressure sensing, and flexible unit conversion systems, air permeability testing equipment significantly improves testing efficiency while reducing human error. It is widely used in PPE manufacturing, textile engineering, non-woven product development, and industrial filtration quality inspection.
The Heat Contact Machine GT-C101 is a specialized testing instrument designed for evaluating the heat resistance and thermal protective performance of gloves, protective clothing, and other heat-resistant materials used in high-temperature environments. In industries such as smelting, casting, welding, and glass manufacturing, workers are frequently exposed to intense heat, making accurate testing of contact heat resistance essential for ensuring safety and compliance.
GT-C101 simulates real working conditions by measuring heat transfer delay and thermal transmission under instant contact with high-temperature surfaces. Fully compliant with EN 407, EN 702, and ISO 12127-1 standards, this machine provides precise, repeatable data for manufacturers, laboratories, and research institutions. With high-temperature capability up to 500°C, advanced calorimetry, digital monitoring, and adjustable contact speed, the Heat Contact Machine GT-C101 is an indispensable tool for developing and certifying next-generation PPE and heat-insulation materials.
Quick links
Products