Analysis of test steps of automobile interior combustion tester
The car interior combustion testing-equipment' target='_blank'>tester adopts the horizontal direction burning performance test method, which is used to measure the relative burning rate and flame retardant performance of various textile fabrics, clothing, tents, especially automobile interior decoration fabrics. (Hong Kong) Co., Ltd. is the manufacturer, welcome Inquiries from customers in need. Applicable standards: GB 8410, ISO 3795, FMVSS 302, DIN 75200, SAE J369, ASTM D5132, JIS D 1201, AU 169. Main parameters: 1. Flame time: 0-999.9s±0.1s adjustable; 2. Delay time: 0-99h59m59.99s±0.1s; 3. Test wind speed: between 0.10m/s ~ 0.30m/s; 4. Test gas: liquefied gas or other combustible gas (such as natural gas, city gas) of 35MJ/m3~38MJ/m3. Test steps: 1. Adjust the test environment with a temperature of 10°C to 30°C and a relative humidity of 15% to 80%. 2. The sample is at least 20mm away from the frame, and the sample holder is installed on the top bracket of the combustion box to ensure that the sample is vertical. 3. Place the marking line horizontally in front of the sample pressing plate. The distance between the marking line and the surface of the sample is 1mm and 5mm respectively, and the marking line should maintain sufficient tension. 4. Light the gas lamp and adjust the flame height to 40mm±2mm, adjust the placement angle of the gas lamp, 30 degrees from the plane where the sample is located°angle. 5. The sample is ignited in the flame of the gas lamp for 5s, immediately extinguish the gas lamp and reset it. 6. If the sample does not burn, it is considered not ignited, and another pretreated sample needs to be re-tested, but the ignition time of the sample in the flame of the gas lamp is 15s. 7. If any one of the three samples in any group exceeds 50% of the minimum value, another group of samples in the same direction should be taken for the test again. If one or two specimens in any group of three specimens do not burn to the third marking line, take another group of three specimens in the same direction and perform the test again. 8. Measure the following times, in seconds (s): a) Time t1 from the start of ignition to burnout of the first marker line; b) Time t2 from the start of ignition to burnout of the second marker line; c) From the start of ignition It is time t3 when the flame burns the three-marked line. 9. Calculation For the sample whose combustion flame reaches at least the first marking line, the combustion speed (Vi) is calculated as follows: Vi=60×(Di/ti) where: Vi——Burning speed, in millimeters per minute (mm/min); i——The flame burns to the one/two/three mark lines, 1, 2, and 3; Di——The burning distance of the flame to the one/two/three mark line, the unit is millimeter (mm); ti——The burning time for the flame to burn the 1/2/3 marker line, the unit is seconds (s). The burning velocity of each sample shall be the larger value of V1, V2 and V3. The burning velocity of a group of samples shall be the test result of the burning velocity of three or more samples, and the calculation result shall be rounded to an integer.
In today's world, have risen to an unexpected level of tensile tester manufacturers. It has gained a lot of popularity and has come up with different kinds of variations in its content.
To know more about and the market trends, go to GESTER Instruments.
GESTER International Co.,Limited, a manufacturer of textile testing equipment, might emphasize less hassle or less wasted time rather than emphasizing reliability or quality.
GESTER Instruments clearly and succinctly expresses what our company is all about. Strong brands cut through the noise to grab the audience and immediately shed light on the character of the product or service.
textile testing equipment is one of the best products sold in the market today.
The air permeability tester is a high-precision testing instrument designed to evaluate the breathability of PPE materials, textile fabrics, non-woven fabrics, woven fabrics, and industrial filter media. It plays a critical role in quality control, product development, and laboratory research across multiple industries including PPE, textiles, automotive interiors, and filtration systems.
Modern instruments such as the GT-C27 Air Permeability Tester are developed with advanced sensor systems, automated control logic, and multi-standard compatibility to ensure reliable and repeatable results. Complying with global standards such as ISO 9237, ASTM D737, DIN 53887, and GB/T 5453, it guarantees internationally recognized testing performance.
With high automation, accurate pressure sensing, and flexible unit conversion systems, air permeability testing equipment significantly improves testing efficiency while reducing human error. It is widely used in PPE manufacturing, textile engineering, non-woven product development, and industrial filtration quality inspection.
The Heat Contact Machine GT-C101 is a specialized testing instrument designed for evaluating the heat resistance and thermal protective performance of gloves, protective clothing, and other heat-resistant materials used in high-temperature environments. In industries such as smelting, casting, welding, and glass manufacturing, workers are frequently exposed to intense heat, making accurate testing of contact heat resistance essential for ensuring safety and compliance.
GT-C101 simulates real working conditions by measuring heat transfer delay and thermal transmission under instant contact with high-temperature surfaces. Fully compliant with EN 407, EN 702, and ISO 12127-1 standards, this machine provides precise, repeatable data for manufacturers, laboratories, and research institutions. With high-temperature capability up to 500°C, advanced calorimetry, digital monitoring, and adjustable contact speed, the Heat Contact Machine GT-C101 is an indispensable tool for developing and certifying next-generation PPE and heat-insulation materials.
Personal protective equipment must meet specific performance requirements before it can be used in demanding workplace environments. ISO, EN, and ASTM standards provide important test methods and performance requirements for different PPE categories. However, the applicable standard depends on the product, intended application, target market, and specific protection requirements.
This guide explains the role of ISO, EN, and ASTM standards in PPE testing and introduces common requirements for safety footwear, protective gloves, protective clothing, masks, and safety helmets. It also explains how laboratories can select suitable PPE testing equipment according to the applicable test method.
Quick links
Products