Analysis of the principle and use of UV ultraviolet aging box
The basic principle of UV aging test box: The damage to materials caused by sunlight and moisture in the nature of UV aging test box causes inestimable economic losses every year. The damage caused mainly includes fading, yellowing, discoloration, strength reduction, embrittlement, oxidation, brightness reduction, cracking, blurring and chalking. Products and materials that are exposed to direct or behind-the-glass sunlight are at greatest risk of photodamage. Materials exposed to fluorescent, halogen, or other light-emitting lamps for extended periods of time are also affected by photodegradation. Application of UV aging box: The UV aging test box uses a xenon arc lamp that can simulate the full sunlight spectrum to reproduce the destructive light waves existing in different environments, which can provide corresponding environmental simulation and accelerated test data for scientific research, product development and quality control. The aging test is carried out by exposing the material sample to the light and thermal radiation of the xenon arc lamp to evaluate the light resistance and weather resistance of some materials under the action of a high temperature light source. It is mainly used for paints, coatings, rubber, plastics, pigments, adhesives agents, fabrics, etc. UV ultraviolet aging box structure: 1. Inner box material: SUS imported high-grade stainless steel plate. 2. Outer box material: The surface of the cold-rolled plate produced by Baosteel is phosphating paint. 3. The filter is made of low iron content tempered glass 5mm. 4. The reflective light adopts high-purity alumina plate. UV aging box control system UV aging test box adopts Korean TEMI brand temperature control instrument, and adopts microcomputer PID temperature controller for temperature control. Irradiance uniformity:±15% (at the sample surface) uses a standard Pt-100 temperature sensor to precisely control the sample surface temperature during the test; the light source uses a visible light xenon lamp with a rated power of 2500W. The lamp tube is installed on the top layer of the instrument, and the spectral energy of the light emission is mainly concentrated at the wavelength between 300 and 780 nm; according to the test spectral irradiance, the irradiance does not exceed 1 to 3 of the corresponding sun (average sunlight at 5:00 noon at the equator in summer). Because the energy output of fluorescent light will gradually decay with time, in order to reduce the influence of the test caused by the decay of light energy, and the effect of GB/T19394-2003 No.5-a on the irradiance uniformity±15% of the requirements, this test chamber is designed to adjust the height of the sample test piece. UV ultraviolet aging chamber parameters: meet the standards: ASTM D4329, ASTM D4587, ASTM D4799, ASTM D5208, ASTM G151, ASTM G154, EN 927-6, EN 1297, EN 1898 FIBC, EN 12224, EN 13523-10, ISO 4892-1, ISO 4892-3, ISO 11507, ISO 11895, ISO 11997-2, SAE J2020, prEN 1062-4. Product advantages: The innovative design, compared with other UV fluorescent aging test chambers, achieves higher standards in terms of performance characteristics, ease of use, accuracy and safety, and its verification performance meets or even exceeds other brands. Multilingual touch screen interface, data acquisition via Ethernet connection, high security, optional recirculation spray device. More other unique user-friendly features. Product features: 1. 8 40-watt UV fluorescent tubes 2. Blackboard temperature (BPT) control 3. Safety protection device: double protection of software and hardware after opening the door; low water level protection; over-temperature protection, etc. 4. Compliant with CE standards and passed UL and CSA certification 5. Sample holder 6. Touch screen display 7. Safety interface for irradiance calibration : 0.35 W/m2 (UVA, UVB) Maximum: 1.55 W/m2 (UVA), 1.23 W/m2 (UVB)3, Black panel temperature range: UV stage– BPT 35-80°C (95-176°F) Condensation stage– BPT 35-60°C (95-140°F) 4. Sample capacity: 48 + BPT on 24 sample clips 5. Weight: about 140KG (310LB), depending on the optional accessories± 10%), 1 Ph., 2 Wire (1/N/PE), 50/60 Hz, 12A230 VAC (± 10%), 1 Ph., 2 Wire (1/N/PE or 2/PE), 50/60 Hz, 8A7, Spray water pressure: 25-40psi(1.7-2.7bar), Purity:<1 ppm dissolved solids, silicon:<0.1 ppm, conductivity:<5 us/cm or 200 kΩ or refer to the test method 8. Condensed water required pressure: 2-60psi (0.1-4.1bra) Purity: Deionized water is recommended, but not required. Accessories: 1. Circulating water spray 2, 12 standard nozzles 3, handheld radiation calibrator 4, data acquisition program via Ethernet 5, overlay kit 6, radiation control (340 nm, 313 nm, 351 nm) 7, Nozzles can be customized for users. More about UV aging test chamber: http://www.standard-group.cc/
There is a strong need for more research on , in order to be able to provide strong and conclusive evidence of their tensile tester manufacturers effects. However, recent studies have provided valuable insights into how the intake of may result in improved tensile tester manufacturers.
Our vision is to realize the tremendous potential of textile testing equipment by providing tensile tester manufacturers services that consistently meet our customers’ expectations.
GESTER International Co.,Limited offers not only the high-quality product but also the finest service, gives the customer with an expressive using experience.
The Heat Contact Machine GT-C101 is a specialized testing instrument designed for evaluating the heat resistance and thermal protective performance of gloves, protective clothing, and other heat-resistant materials used in high-temperature environments. In industries such as smelting, casting, welding, and glass manufacturing, workers are frequently exposed to intense heat, making accurate testing of contact heat resistance essential for ensuring safety and compliance.
GT-C101 simulates real working conditions by measuring heat transfer delay and thermal transmission under instant contact with high-temperature surfaces. Fully compliant with EN 407, EN 702, and ISO 12127-1 standards, this machine provides precise, repeatable data for manufacturers, laboratories, and research institutions. With high-temperature capability up to 500°C, advanced calorimetry, digital monitoring, and adjustable contact speed, the Heat Contact Machine GT-C101 is an indispensable tool for developing and certifying next-generation PPE and heat-insulation materials.
The air permeability tester is a high-precision testing instrument designed to evaluate the breathability of PPE materials, textile fabrics, non-woven fabrics, woven fabrics, and industrial filter media. It plays a critical role in quality control, product development, and laboratory research across multiple industries including PPE, textiles, automotive interiors, and filtration systems.
Modern instruments such as the GT-C27 Air Permeability Tester are developed with advanced sensor systems, automated control logic, and multi-standard compatibility to ensure reliable and repeatable results. Complying with global standards such as ISO 9237, ASTM D737, DIN 53887, and GB/T 5453, it guarantees internationally recognized testing performance.
With high automation, accurate pressure sensing, and flexible unit conversion systems, air permeability testing equipment significantly improves testing efficiency while reducing human error. It is widely used in PPE manufacturing, textile engineering, non-woven product development, and industrial filtration quality inspection.
Quick links
Products