Textile electrostatic properties electrostatic decay GB33728 test
The GB/T33728-2017 standard specifies the test method and evaluation of the electrostatic decay time of textiles, which is applicable to all kinds of textile fabrics, and other film materials can be used for reference. The electrostatic decay performance tester is an evaluation instrument. (Hong Kong) Co., Ltd. is the manufacturer. Customers who have demand are welcome to inquire. Electrostatic decay time refers to the time required for the voltage across the pad sample to decay to a given percentage of its initial value. After the sample was charged to 5000V, the power was turned off, the voltage on the sample was attenuated by grounding, and the time required for the voltage to decay to 500V was measured. Test device: The electrostatic decay tester consists of a high-voltage generator, a non-contact electrostatic field strength meter, a timer, a sample holder, a metal shield and a display. Experimental conditions: A: The temperature is 23±3°C, relative humidity of 12±3%; B: The temperature is 20±2°C, relative humidity of 35±5%; C: temperature is 23±3℃, relative humidity of 50±5%. When using other test environmental conditions, it should be indicated in the test report. Sample preparation: If necessary, wash the sample according to the 4A procedure in GB/T8629-2001. After washing, the sample should be dried at 60°C for 1 hour, or the number of times approved by the relevant party to be washed and dried. Randomly sample 3 pieces from the sample, and the size of each sample is (70±5) mm×(140±5) mm. When the sample has different characteristics in the warp and weft direction (straight and horizontal direction) or front and back, or the characteristics cannot be determined, it is necessary to sample separately, each group of 3 samples. The above-mentioned samples should be allowed to stand for not less than 24 hours in the specified test environment. Test procedure: 1. Fasten the sample on the fixture in the metal shield, ensure that the sample is parallel to the probe, the exposed area of the center of the fixture shall not be less than 2500mm2, and the sample shall be de-energized to the zero point. Then close the metal shield. 2. Adjust the high-voltage generator, apply voltage to the sample, and stabilize the sample to 5000V. If the sample cannot be electrified to 5000V, record that the sample cannot be electrified and stop the test. 3. Stop powering on the sample, start the timer and ground the sample at the same time, read the time when the voltage of the sample decays to 500V and record it, stop the test when the decay time is greater than 60s, and record the test result as greater than 60s. 4. Adjust the high-voltage generator, apply voltage to the sample, and make the sample electrified to -5000V. If the sample cannot be electrified to -5000V, it will be recorded that the sample cannot be electrified, and the test will be stopped. 5. Stop powering on the sample, start the timer and ground the sample at the same time, read the time when the voltage of the sample decays to 500V and record it, stop the test when the decay time is greater than 60s, and record the test result as greater than 60s. 6. Test the remaining samples in accordance with the test procedures 1-5. Result evaluation: Take the maximum value of the electrostatic decay time of the positive and negative voltages as the test result, and keep two significant figures for the result, and the unit is s. If the test time exceeds 60s, it will be recorded as>60s, if it cannot be pressurized to 5000V, it is recorded as not applicable (N/A). If necessary, the electrostatic properties of textiles can be evaluated according to the following table. If it occurs, the positive and negative voltage decay time grades are different, and the evaluation shall be carried out according to the result of the lower grade. Technical requirements for electrostatic decay time:
It is beyond doubt that benefits tensile tester manufacturers. Market sentiments are strong, especially in the light of growing tensile tester manufacturers observed globally.
Serving others for customers a better life with textile testing equipment for employees respect and opportunity.
The trend toward using tensile tester manufacturers textile testing equipment to ease tensile tester manufacturers, once established, soon extended into such additional fields as tensile tester manufacturers and tensile tester manufacturers.
The global market is estimated to reach a value of almost tensile tester manufacturers in the next decade. have a robust position in the tensile tester manufacturers market because of its proven high potency in tensile tester manufacturers.
Personal protective equipment must meet specific performance requirements before it can be used in demanding workplace environments. ISO, EN, and ASTM standards provide important test methods and performance requirements for different PPE categories. However, the applicable standard depends on the product, intended application, target market, and specific protection requirements.
This guide explains the role of ISO, EN, and ASTM standards in PPE testing and introduces common requirements for safety footwear, protective gloves, protective clothing, masks, and safety helmets. It also explains how laboratories can select suitable PPE testing equipment according to the applicable test method.
The Heat Contact Machine GT-C101 is a specialized testing instrument designed for evaluating the heat resistance and thermal protective performance of gloves, protective clothing, and other heat-resistant materials used in high-temperature environments. In industries such as smelting, casting, welding, and glass manufacturing, workers are frequently exposed to intense heat, making accurate testing of contact heat resistance essential for ensuring safety and compliance.
GT-C101 simulates real working conditions by measuring heat transfer delay and thermal transmission under instant contact with high-temperature surfaces. Fully compliant with EN 407, EN 702, and ISO 12127-1 standards, this machine provides precise, repeatable data for manufacturers, laboratories, and research institutions. With high-temperature capability up to 500°C, advanced calorimetry, digital monitoring, and adjustable contact speed, the Heat Contact Machine GT-C101 is an indispensable tool for developing and certifying next-generation PPE and heat-insulation materials.
Safety gloves are critical personal protective equipment (PPE) used in industries such as manufacturing, welding, construction, firefighting and chemical processing. To ensure reliable protection, gloves must undergo strict performance testing before entering the market.
Professional gloves testing equipment helps manufacturers evaluate important properties including cut resistance, thermal protection, contact heat resistance, tensile strength and impact protection. By selecting suitable testing machines, companies can improve product quality, meet international standards and reduce safety risks.
This complete buying guide introduces the main types of glove testing equipment, explains their applications and provides practical advice on choosing the right solution for your laboratory or production requirements.
Choosing the right abrasion testing equipment is essential for obtaining accurate and repeatable wear resistance results. DIN Abrasion Tester and Taber Abrasion Tester are two widely used abrasion testing machines, but they are designed for different material types and testing purposes.
This article provides a detailed comparison between DIN Abrasion Tester and Taber Abraser, covering their working principles, specimen requirements, industry applications, standard compliance, technical characteristics, operation features and practical advantages. DIN Abrasion Tester is mainly designed for rubber, elastic materials, tires, conveyor belts and footwear soles, while Taber Abrasion Tester is suitable for flat materials such as coatings, textiles, plastics, leather, metals and decorative surfaces.
By understanding the differences between these two abrasion testing methods, laboratories can select the most suitable abrasion tester based on sample geometry, testing standards and production quality control requirements.
Quick links
Products