loading

PPE Testing Equipment Manufacturer | Safety Equipment Testing Machines | GESTER


Products

How to Select an Abrasion Tester for Different Footwear Materials

Compare 10 Types of Footwear Abrasion Testers for Leather, Textile, Rubber Soles, and Shoelaces
What is a Footwear Abrasion Tester
What is a Footwear Abrasion Tester

It is important to understand the different types of abrasion testers in order to choose the appropriate one for particular footwear‑material testing requirements. This article provides a broad general overview of the classification of abrasion testers based on testing principle, target footwear materials, and test purposes.

What is a Footwear Abrasion Tester?

The footwear abrasion testers are laboratory instruments used to evaluate the abrasion resistance of footwear-related materials, including leather, textile uppers, rubber soles, shoelaces, and shoe accessories.


Through controlled friction and repeated rubbing movements, these instruments simulate material wear during everyday use. Depending on the testing method, they can measure material mass or volume loss, surface damage, pilling, or color transfer.


Different abrasion testing machines use different testing principles, loads, abrasive media, and sample fixtures. Selecting the appropriate equipment helps footwear manufacturers, material suppliers, and testing laboratories obtain reliable results for material selection, product development, and quality control.

Types of Footwear Abrasion Testers

A Martindale abrasion tester is built for evaluating abrasion resistance of footwear vamp, lining, textile and coated‑fabric materials. During the Martindale abrasion test, specimens rub against a standard abradant following a Lissajous motion under controlled pressure. This method helps assess surface wear, fabric damage, and resistance to repeated friction.


It is often equipped with multi‑station designs including 4‑station, 6‑station, 8‑station and 9‑station options. It features touch‑screen PLC control and quick‑release sample holders, allowing inspectors to take out individual specimens for visual check without stopping ongoing testing cycles. This instrument complies with ISO 12947, ISO 20344, ASTM D4966 and SATRA TM31 standards. It delivers minimum‑to‑moderate friction intensity for upper textile and lining material assessment


When comparing different Martindale abrasion test standards, buyers should confirm the required specimen preparation, test pressure, abrasive materials, and evaluation criteria.

DIN abrasion resistance tester is widely used for elastic polymer and rubber‑based footwear components, especially shoe outsoles. The test specimen presses against rotating abrasive drum under configurable standard weight loads, calculating material volume loss after fixed abrasion travel distance.


These din abrasion testers follow DIN 53516, ISO 4649, SATRA TM174 test specifications. They are solidly constructed to handle rigid rubber and elastomer samples. It works well for safety footwear soles, casual shoe outsole rubber compound comparison in factory QC labs and third‑party testing institutions.

3. IULTCS Veslic Leather Abrasion Tester 1‑Position GT‑KC01‑1

Single and Two‑position Veslic leather abrasion tester targets leather surface color‑fastness performance. Under specified pressure, standard white wool felt carries out reciprocating rubbing movement against dyed leather or plastic sample surface. Operators assess color fading of specimen and staining degree of wool felt after preset rubbing cycles; both dry‑rub and wet‑rub test modes are supportedGester.


This machine fits small‑batch leather quality inspection. It meets ISO 11640, DIN 4843 and SATRA PM173 standards. It is mostly applied for finished shoe upper leather, synthetic leather decorative surface quality verification.

Uppers color fastness rubbing tester focuses on color‑transfer risk of printed or dyed shoe upper fabrics and synthetic leathers. It completes reciprocating friction cycles under standardized pressure settings to check whether surface dye will rub off onto contact medium.


This equipment is commonly adopted in footwear production lines for incoming‑material inspection. It supports both dry‑state and wet‑state rubbing tests, helping manufacturers avoid color‑stain complaints on finished footwear goods.

Taber abrasion tester uses two freely rotating abrasive wheels applying vertical load onto horizontally rotating flat specimens. Rotary friction simulates diversified surface wear conditions for flat footwear‑component samples such as insole sheets and decorative synthetic panels.


Different abrasive wheels can be swapped to adjust abrasion aggressiveness. This taber type abrasion tester suits multi‑material comparative screening for flat, rigid or semi‑rigid footwear materials in commercial footwear laboratories.

Rubber DIN abrasion tester is dedicated for vulcanized rubber and elastic sole materials. It shares core DIN‑standard testing principle with DIN Abrasion Tester KB03B‑3 and delivers volumetric wear‑loss measurement results.


These units are engineered for heavy‑usage testing environments. It can process large quantities of rubber sole compound samples, widely selected by rubber‑material suppliers and footwear R&D departments for new‑formula performance comparison work.

Shoelace and eyelets abrasion testing machine is purpose‑built for shoelace and shoe‑eyelet component durability test following SATRA TM93 method. Shoelace samples pass through standard metal eyelet fixtures under fixed tension force, and repeat pull‑rub cycles run until lace breakage or visible damage appears.


Multiple test stations run at the same time. It helps manufacturers validate shoelace raw‑material quality and eyelet hardware wear‑resistance performance for finished footwear.

AKRON abrasion tester works for vulcanized rubber soles and high‑elastic elastomer footwear materials. The specimen tilts at a set angle and presses against rotating abrasive wheel to generate inclined‑surface friction wear.


This tester measures mass loss after defined abrasion cycles. It is widely used for heavy‑duty footwear outsole material assessment for work shoes and outdoor footwear product development.

Sole abrasion resistance tester is designed for complete shoe‑sole piece abrasion evaluation. Real shoe‑sole samples instead of small lab coupons can be mounted for testing, simulating actual outsole wear condition closer to real‑life service scenarios.


These testers are preferred by footwear brand labs for finished‑product verification. It offers practical wear‑performance reference for whole‑shoe quality auditing.

NBS rubber abrasion tester complies with ASTM D1630 and SATRA TM221 standards, focusing on vulcanized rubber sole and heel compounds. Specimens are pressed against coarse‑grit sandpaper wrapped on rotating metal drum with fixed 22 N test load, measuring volume loss after abrasion runs.


It is suitable for comparative screening of rubber sole formulations. Note that this tester is not recommended for test samples thinner than 2.54 mm. It is a common quality‑control instrument inside footwear rubber‑component factories.

Key Factors to Choose the Right Abrasion Tester

When selecting abrasion tester equipment for your footwear lab, several critical points need consideration, similar to picking electrical meter boxes for electrical installations:

1. Footwear material type:

Confirm whether your test samples are textile uppers, dyed leather, rubber soles, shoelace accessories or composite panels. Different material families require corresponding friction principles.

2. Applicable test standards:

Verify which international or industry standards your products must meet, including ISO, SATRA, ASTM, DIN specifications. Each tester model supports specific standard sets.

3. Sample geometry:

Check if you test small lab‑cut coupons or full‑size shoe‑sole pieces; some machines only accept standardized small specimens.

4. Laboratory throughput needs:

Decide single‑station or multi‑station models based on your daily testing volume to improve inspection efficiency.

5. Test output requirement:

Clarify whether you need volumetric wear‑loss figures, visual surface‑damage observation, or color‑fastness staining assessment, as different testers deliver different types of test data.

Frequently Asked Questions

Q1: Can one abrasion tester handle all footwear materials?

A single abrasion tester cannot satisfy all footwear abrasion testing demands. Each tester adopts a unique friction motion and load setup designed for specified materials and standards. For example, Martindale works for upper textiles, while DIN and NBS testers are made for rubber soles. If you test mixed materials, your lab may need multiple test instruments.

Q2: What is the difference between abrasion resistance test and rubbing color fastness test?

Abrasion resistance focuses on material wear, mass loss, surface scratch and structural damage after repeated friction. Rubbing color fastness only checks dye transfer, fading and staining. Veslic and upper rubbing testers are built for color fastness, while Martindale, DIN, NBS and Akron machines are mainly for abrasion resistance evaluation.

Q3: Do I need to prepare standard abradants and consumables for abrasion resistance testing machines?

Yes. Almost all footwear abrasion testers require matched consumables, such as standard abrasive paper, wool felt, abrasive wheels, sample clamping films and pressure weights. 

Q4: Are these abrasion testers suitable for third‑party testing laboratories?

All models listed in this guide comply with widely accepted ISO, ASTM, DIN and SATRA standards. They are suitable for factory QC labs, brand internal labs and accredited third‑party test institutes that need formal test reports for footwear export and certification.

Q5: Can I test finished whole shoes instead of cut samples?

Only the dedicated sole abrasion tester supports mounting complete shoe soles or whole footwear for testing. Most other abrasion instruments require cutting standard coupons from raw materials or shoe components before testing.

Q6: What maintenance work should be done regularly for abrasion test equipment?

You should replace worn abrasive media on schedule, clean friction tracks, calibrate test loads and counter systems, and check clamping fixtures before each batch of tests. Regular calibration helps avoid deviation and ensures test reliability over long‑term operation.

Q7: How do I choose a reliable abrasion testing machine tester manufacturer?

When selecting an abrasion test testing instrument manufacturer, consider its experience in manufacturing material testing equipment, product range, technical support, and ability to provide equipment that meets relevant international testing standards. It is also important to confirm calibration support, spare parts availability, and after-sales service to ensure long-term testing reliability.

Conclusion

Different types of footwear abrasion testers exist with the capability of meeting different laboratory and factory testing needs, from compact single‑station units for small‑batch QC to multi‑station heavy‑duty testers for high‑volume material screening. This guide would aim at offering relevant information needed to arrive at the right decision concerning shoe material abrasion test requirements.

Abrasion Testing Machine

Contact Us for a Free Demo or Consultation

For more information on Abrasion Testers, contact us for further support. 

- Email: info@gester-instruments.com

Contact GESTER for Abrasion Tester
prev
Essential Guide to Universal Testing Machine Maintenance for Optimal Performance
Recommended for you
Get in touch with us
GESTER International Co., Ltd. gains certificates of ISO 9001, 3A and SGS Audited supplier etc. with advanced design concept, excellent manufacturing technology and strict quality control.
WeChat
Contact us
Tel: +86-595-28886108 
Fax: +86-595-22515221
E-mail: sales10@gester-instruments.com,
                 info@gester-instruments.com
Mobile/Whatapp/ Wechat:  
             + 86(0)18059983973
Address:  No.15, Chifeng Road,Licheng Region, Quanzhou city of Fujian,PR China.
Customer service