Interpretation of Test Test of Digital Fabric Air Permeability Meter

The digital fabric air permeability tester is used to measure the air permeability of various materials such as textiles, clothing and non-woven fabrics. 

Applicable standards: GB/T 5453-1997, GB/T 13764, ASTM D737, ISO 9237, ISO 5636 

Main parameters: 

1. Differential pressure range: 0～4000Pa; 

2. Measurable air permeability: 0.2—12826mm/s; 

3. Measurement error:≤±2%; 

4. Measurable fabric thickness:≤12mm; 

5. Suction volume adjustment: dynamic adjustment by data feedback; 6. Sample area setting circle: 

5cm2, 20cm2, 50cm2, 100cm2; 

7. Nozzle: 11 in total. 

The air permeability of the fabric refers to the performance of the fabric through the air when there is a pressure difference on both sides of the fabric. That is, under the specified pressure difference between the two sides of the fabric, the volume of air flowing through the unit area of the fabric per unit time, the unit is L/mm2·s. Because the pressure difference is a necessary condition for air to flow, only when a certain pressure difference is maintained on both sides of the fabric to be tested can air flow in the fabric. 

Air permeability tester for fabric Test method: The air permeability requirements of different fabrics are very different. Even if the same fabric has different requirements for use, the pressure difference between the two sides of the fabric is often different. pressure drop for testing. The test method is to test the airflow through the fabric with a certain pressure difference, so as to obtain the air permeability of the fabric. Most of the wearing fabrics can be considered relatively sparse, and the pressure requirements used in the test are relatively low. At this low pressure level, it is customary to use a vacuum pump to extract air to achieve the required pressure difference, and read the gas flow from the flow meter. The key technology of the digital fabric air permeability meter is the measurement of pressure and flow. 

The Air permeability tester for fabric of our company uses an orifice flowmeter to measure the airflow and a U-shaped tube to measure the air pressure. The orifice plate has been used as a flowmeter device for more than a hundred years, and many national and international standards have been promulgated based on it. The orifice plate is used as a blocking plate for measurement in narrow pipes and forces the flowing material to be squeezed. When the fluid that fills the pipeline, when it flows through the throttling part in the pipeline, the flow beam will form a local contraction at the throttling part, and the static pressure will decrease, so a pressure difference will be generated before and after the throttling part. The greater the pressure difference, the flow rate can be measured according to the pressure difference. In many installations, the use of orifice flow meters is common. There are also some fabric air permeability test instruments that use venturi tubes and the like to measure flow. Compared with the orifice plate, the Venturi has less pressure loss and longer life. Whether it is an orifice throttling device or a venturi throttling device, the measurement method is based on the flow continuity equation (the law of conservation of mass) and the Bernoulli equation (the law of conservation of energy), which is suitable for measuring stable airflow. 

The following conditions must be met when using a standard throttling device for flow measurement: 

(1) The measured medium fills the entire pipe section and flows along a circular pipe with an inner diameter of not less than 50mm; for a Venturi pipe, its diameter should not be less than 100mm It should not be larger than 800mm. 

(2) The flow beam in the pipeline is stable, or can be considered to be stable in fact (when the flow beam is stable, the flow velocity and pressure do not change with time at the same point) 

(3) When the measured medium passes through the throttling device , its phase state remains unchanged (for example: the liquid does not evaporate, the superheated steam is still superheated, the gas dissolved in the liquid does not precipitate, etc.), and a single phase exists at the same time. For media with complex components, it should only be used if its properties are similar to those of single-component media.

If you are looking to get started with Air permeability testing equipment, it's important to find a quified . Let GESTER International Co.,Limited be your provider. Visit us at GESTER Instruments.

Check out GESTER Instruments for optimal quality products, and get your Automatic Air Permeability Tester problem fixed. Send us an enquiry or make a call if you are interested.

can be used in a wide variety of ways.